글

LATEST FROM THE FIX BENCH

Latest appliance fixes

Browse all fixes →

Dehumidifier Runs but Collects No Water: Check Humidity, Temperature, and Airflow

An empty dehumidifier bucket can mean the room is already below the set point, water is leaving through a hose, or the machine is not removing moisture. Check actual relative humidity, room temperature, airflow, bucket seating, and drainage before deciding that the compressor has failed. An empty bucket is not automatically a fault when room humidity is already low. Created by FIX Start with a separate humidity reading Place a hygrometer near the dehumidifier, but not directly in its warm exhaust. Compare that reading with the selected humidity. ENERGY STAR notes that a built-in humidistat cycles the unit once the desired level is reached; a machine set to 50% may run its fan or cycle without filling the bucket when the room is already near or below 50%. Give the reading time to settle after moving the hygrometer. If the room is clearly damp and remains well above the set point for several hours, continue through the checks. A musty smell alone is not a measurement, and a plumbing...
Read fix →

Vacuum Losing Suction? Check the Bin, Filters, Hose, and Brush Roll in This Order

A vacuum that suddenly stops picking up usually needs an airflow check before it needs a motor diagnosis. Empty the bin, inspect the filter, separate the wand or hose, and then check the cleaner head. That order isolates the restriction without opening the motor housing or guessing at an electrical fault. A full bin and restricted airflow can imitate a failing vacuum. Created by FIX Stop first if the problem looks electrical Switch the vacuum off and disconnect it from the wall or charger before touching the bin, filter, wand, hose, or brush roll. Stop using it if the plug or cable is damaged, the casing becomes unusually hot, a breaker trips, or there is a burning smell, smoke, crackling, or sparking. Those signs are not an airflow-cleaning job; contact the manufacturer or a qualified repair service. If the vacuum simply sounds different, pulses, or leaves debris behind, let it cool and follow the external checks below. Keep the model manual nearby because filter locations, washa...
Read fix →

Dryer Taking Too Long? Check the Lint Screen, Load, Settings, and Exhaust Airflow

A dryer that needs two cycles may be moving too little air, carrying the wrong load, or using a setting that ends early. Begin with the lint screen, load, selected cycle, and visible exhaust. Stop using the dryer if you smell burning, see scorching, hear scraping, or the plug, cord, or outlet becomes unusually hot. Slow drying is often an airflow or load problem before it is a parts problem. Created by FIX Clean the lint screen before the next load Remove the screen according to the owner manual and roll lint away with your fingers. Inspect it under good light. Fabric-softener residue can create an almost invisible film; if the manual permits washing, use warm water and a soft nylon brush, then dry the screen completely before reinstalling it. Never run the dryer without the screen. A screen that looks only partly covered can still restrict airflow. Created by FIX Give laundry room to tumble A packed drum keeps wet fabric bundled together, while a tiny load may not contact moisture ...
Read fix →

Dishwasher Leaves Dishes Wet? Check Rinse Aid, Cycle, Loading, and Plastics

If glass and ceramic come out dry but plastic is dotted with water, the dishwasher may be working normally. Plastics store less heat, recesses trap water, and energy-saving cycles may use less drying. Before assuming a failed heater, check the rinse aid, selected options, loading angles, and which materials are actually wet. Wet plastic does not always mean the dishwasher failed to heat. Created by FIX Compare materials and locations After a full cycle, compare a ceramic plate, a glass, metal cutlery, and a plastic container. Water only on plastic or in the concave bases of mugs usually points to material and loading rather than a universal drying failure. A wet tub wall can also be normal on condensation-drying models. Check the rinse-aid indicator Rinse aid lowers water's surface tension so droplets sheet off dishes. Check the dispenser with the door fully open and refill only with a product labeled for automatic dishwashers. Wipe spills and close the cap. If the model allows ...
Read fix →